< img height="1" width="1" style="display:none" src="https://www.facebook.com/tr?id=4630387973710942&ev=PageView&noscript=1" />
market01@bjholland.com webmaster@bjholland.com
English
English русский Português

Tin Plating line

Product Category

Related Product

Related Cases

Tin Plating line
Tin Plating line
Tin Plating line
Tin Plating line
Tin Plating line
Tin Plating line
Tin Plating line
Tin Plating line
Chat with us Leave a message market01@bjholland.com

Our Automatic Tin Plating Line is a through-type coating line for bus bar plating. The speed of production, the smoothness, brightness and color of the plated surface are well improved than traditional plating lines. Through the tin plating process, the conductivity and antioxidation of copper sheets has been increased.

The line is consists of the mechanical part and the plating part. This line works in a closed condition: the water in the cleaning process can be recycled, and the waste gas can be collected and treated.

 

Advantages:

No wastewater and waste gas emission.

Continuously movement.

Bright and uniform surface plating. 

Release operator from hooking/unhooking job.

Technical parameter

No

Item

QTY

1

 Type

 W150

2

 Copper busbar width range

 30-150mm

3

 Copper busbar thickness range

 1- 25 mm

4

 Production speed

 1.3-3m /min

5

 Total power

 About 50Kw

 

Description of main components

1 Copper busbar feeding rack:

Put the bright busbar horizontally on the feeding rack; the rack can automatically turn over the busbar to vertical status and send it to the cleaning channel by feeding rollers.

2 Conductive flush cleaning section:

After receiving the signal, the hauling device will clamp the busbar and the conductive wheels will contact the busbar. During this section, the busbar will go through the electrolytic degreasing and oil-removing process.

3 Antioxidation cleaning section:

The antioxidation cleaning process is the last cleaning paragraph before the tin plating.

4 Tin plating section:

The tin plating section is divided into three parts, which can ensure the busbar gets the uniform plating effect and plating thickness.

5 Cleaning after plating:

This process is to clean the residual acid at the busbar’s surface

6 Warm water cleaning section:

This process is for the further cleaning

7 Hot wind drying section:

In order to clean the residual water on the busbar surface after cleaning, hot wind drying is adopted to remove the water.

8 Take up and overturn rack:

After the tin plating, the vertical busbars pass the conveying roller rail, then turn to the horizontal status and slip into the stacking device through rubber wheels. In order to avoid the scratch, the slipping distance can be adjusted.

9 Electric control system:

The system consists of 1 main control cabinet and 2 consoles. The control system is divided into plating parts and mechanical parts.

Each section of the plating part is equipped with a hauling device, which receives the signal through the photoelectric sensor and carries out the hauling action.
The worker can set the voltage and current in the control cabinet.

10 Waste gas collecting and cleaning tower: 

After the heating, the acid in the tin plating tanks will generate a small amount of acid mist. In order to reduce air pollution, the waste gas will be collected and sent to a cleaning tower for purification.

11 Waste water purify treatment device:
There is a small amount of waste water in the cleaning cycle of tin plating production. The waste water can be neutralized and filtered by purifying device to reach the standard of reuse water.

 

The requirements of the production line

1. User should prepare a control switch box and power cord used for connecting the control switch box to the main control cabinet of the equipment.

2. Water requirement: soft water 2t

3.  Auxiliary materials: we provide the list

4. Workshop requirement: 45m*6m*4m (L*W*H)

MESSAGE